Fronius Push - Inverter+Meter Daily Logdata

Can you please provide a screenshot of these spikes, today’s graph looks normal with no gaps or 0W recorded on consumption or generation during daylight.

The graph sample below is for today’s 06/July log data up to 5:00PM

The below is what is happening, the settings for both the log data and inverter push were the same. As soon as generation was greater than consumption , this is what was happening:

The hourly log data push would fix it, and then the next 5 minute inverter/meter push would revert back to the spikes.

Hi BB, i have had no problem with my average power readings at all,data taken straight for inverter via Fronius push to PVorg, now i have no average power readings, how can i fix this please thanks jim

Somewhat similar issue here.

I trialled the Daily Logdata push, but 2 - 3 days in to it I noticed a few zeros happening through the daylight hours in the Power Used column - something I’d not seen since getting the LAN connection. There’d only be 4 - 5 per day, but the majority would be on a 55 minute push.

So I dumped the Daily Logdata push leaving the other two Inverter and Meter scripts untouched, however this morning I realised that there’d been whole columns of overnight data missing when the Power hits zero (sunset to sunrise). It’s not total some nights, but can change at midnight to include Energy, Efficiency, Average and Normalised as below -

The remaining Inverter and Meter push scripts haven’t been edited since I removed the ‘overnight’ patch (NoDayEnergy?) some months ago after a firmware fix, and there’s been no missing data or zeros prior to this recent Daily Logdata trial. I’ve rechecked the Inverter and Meter push scripts and they appear complete/uncorrupted.

[Edit - Mid-afternoon and no zero consumptions so far today, but two instances of zero generation have been recorded on a fairly bright day. I’ve just done a Datalogger restart to see if things are any different this evening]

i have not altered the inverter script and how now noticed that PVO is showing a greater running energy and total energy the the direct WLan feed straight from the inverter, the gap slowly gets wider during the day and is about 0.3 kw at the end of the day. i have never had a difference of more 10 watts before so something is off, BB if you can tell me how to get the average power back i will see if that fixes it, i have a inverter, NO meter or other device in this system,straight fronius push setup, my system name is Jims maxim jinkos 6.625kW thanks for your thoughts and help with this Jim

@jimdcollie see here Fronius Push - Dropping DAY_ENERGY.
On Friday there was a change, and now the inverter script is calculating daily energy from the power values, rather than using the actual energy counter in the Fronius push - which may account for your discrepancy.
If you weren’t having any trouble with your pushed data from the inverter before, try adding ‘&dayenergy=1’ to the end of the push upload line inside your Fronius inverter to restore the function back to how it was working last week. This worked for me.

1 Like

thank you i will try that when the inverter is on line tomorrow

Sorry, the &nodayenergy=1 option is now default, please use &dayenergy=1 to explictly enable the recording of DAY_ENERGY

Thanks for the screenshot, when the log data push was added, did the meter push have &n=1 option or &auto=1 ?

You’re currently using &n=1

I tried both options over two separate days. Up to now I have always used &n=1 as I have had no issues with the push to PVOutput, but when I saw the data log push option, I changed to &auto=1 as that was what people were using.

This is with &auto=1 for both inverter and data push running for the day:

I thought that the &auto=1 was not working for me, so I then reverted back to the &v3=none for both inverter and data push and kept it running for the day:

I have since reverted back to the &v3=none for the inverter pushing to PVOutput and the log data push to froniuslog.jsp which is still currently running for the last few days, and my PVOutput looks normal

The auto=1 setting should be set at the start of the day (or the day before) since it relies on the first push of the day to work out how much as been imported/exported during subsequent pushes.

Enabling auto=1 in the middle of the day would produce some strange results.

Another combination of pushes to try is the following -

  1. Inverter Push (froniuspost.jsp)
  2. Meter Push (froniuspost.jsp?n=1&delay=10)
  3. Log Push (froniuspost.jsp)

The froniuslog.jsp push can be stopped.

I have stopped the log push to froniuslog.jsp. I will change the inverter push and log push to PVOutput to auto=1 now (from v3=none), this evening, to let it roll over for the start of the day, as previously, both instances were started in the morning. We will see how it goes.
My meter push is currently set up as n=1&delay=15 which has been working fine.


After making the change to auto=1 yesterday evening, my feed was fine until 13:15 this afternoon when consumption data was incorrect for 25 minutes:


Now this is the weird thing. The hourly log data push fixes this bad data, as shown here from the push at 15:00:


but the next inverter push at 15:05 makes the bad data reappear again until the next hourly data log push.

As per your suggestion, I then stripped off the settings for the inverter and log data push (removed &auto=1), but after the hourly update, the bad data still comes back on the next inverter/meter push:

I have now removed the hourly push and reverted my inverter push back to v3=none for the time being.

This is probably due to the net delay, the meter net pushes are being held for 15-minutes after the log pushes corrects the data, then overwrites it.

It should be okay to reduce delay down to 5-minutes i.e. &delay=5.

However, the next log push one hour should fix this again, but the 0W still exists.

The log pushes don’t seem to be pushed every 1 hour for this system -

e.g. processing times in Perth time 11/Jul and it has not sent any more log pushes since.

  • 12:01
  • 13:01
  • 14:00
  • 15:00
  • 16:01
  • 16:37
  • 16:41
  • 17:00
  • 17:07
  • 17:21
  • 17:22

The erratic log pushes after 16:00 is me testing to see what happens. I do not understand why a log push at 16:00 fixing bad data seen at 13:30, is then reverted back to bad data by a 5 minute push at 16:05. I removed teh log data push after 17:22. I have put the log data push back and changed the meter delay to 5 minutes.

Please keep the settings that is currently working.

Will have a closer look at this, it maybe the combination of log push and net data that is causing issues.

Thanks for your help and patience.

No problem. Appreciate the quick response. The log data push is now reinstated and immediately fixed the bad data between 13:15 and 13:35 when it pushed at approx 19:46, but again the 5 minute meter / inverter push at 19:50 reverted back to the bad data between 13:15 and 13:35.

Found the issue with this, the net data pushes actually keeps the entire history of net pushes received, this would refresh all existing records and overwrite the log data push with incorrect history net data.

This has been fixed to only use the last 40-minutes for Fronius meter net push data.

Excellent. Well spotted and corrected.
I left the three pushes running, and the data for yesterday is now only showing the good data.
Outstanding investigation and solution sourced as usual.

Looks good, this is finally working as expected. Hourly log data is fixing the 0W recorded by the net meter push and is not being overwritten.

Guinea pigs for the greater good is never an issue. We are always happy to test.