looking at my and others ssytems there seems to be a problem after about 08.20 today - no one’s system is updating.
2 Likes
Pushes say they are working
, but PVOutput does not update. Trying through LiveLoader says the data has been uploaded but nothing is updated ,
1 Like
I don’t understand this “push” thing - I’m not very techy but maybe data is going up to PVOUTPUT but the system is just overloaded and is queueing the updates - maybe it will catch up in an hour or so? Perhaps BB could comment?
The “Push” is the data outputing direct to PVOutput from the inverter using my accounts System ID and API as a target referenced here: Push Services — PVOutput documentation. From the other comments it is possible. Worst case, can pull the data from the inverter and upload when the system is working again effectively
Same here. I uploaded data manually via the Oxley app at 10:25 UK time - it indicated a successful upload but 30mins later it’s still not showing. I’ll leave it a while and report back later.
Update at 13:10 - it’s now updated, so it’s obviously having a bad day: probably a hangover from yesterday’s outage.
Same here. All systems lag behind.
Updates now slowly and with small intervals are registrated. Last update was at 10.50h. Current time is now 12.20h
the same issue in the UK here…push’s going through fine…but updates are sporadic at best…on a normal day all updates are going through every 5 minutes without issue
I have basic setup just to have PVO pull data from Enphase and nothing is showing today 11/20 8:15am est even though Enphase site does have some minimal data. I will wait another hour for more to accumulate but even the lowest of production usually shows up on PVO right away so I think too there is a potential issue on the PVO side unless they are having issues with the API pulling data from Enphase site for some or all systems. Uploads is not the issue, the data from Enphase to PVO is the issue. BBloke will have to confirm. But as you can see hopefully in this picture there are a few systems not yet reporting either yet as I said my enphase account has data.
Update of PVO on 20-11-2024 stops again after some registrations at 12.15h. Actual time is now 15.00h (in Holland)
My last update is 03:10. Time now is 07:18. I know I am uploading to PVO but it is not updating on my portal.
UPDATE - Some records of both my systems now updated and filling in the gaps, so I assume the system will eventially catch up to current values and all will be well.
11:15am last update for me in the UK. Considering PV went offline the other day for a few hours which is the first time I’ve ever noticed it in some 10 ish years and now this, i am guessing something is “up” with PV again. That’s about as technical as I get
2hrs later still no data at all for 11/20/2024 at 10:15am EST. BBLOKE will have to check his API interaction to Enphase site or his loading process or…
Yep, 10:15am is my last upload showing today too. I am in the UK, but I don’t think that is relevant.
I have my own app on a Rasperry PI doing the uploads directly to PVOutput. Its log shows that the every 5min batch uploads are being successful, they just aren’t appearing on my site’s webpage.
Cheers, Jim.
Same here in Belgium, last update 20/11 12:10 but upload is reported ok by SBFspot on my raspberry pi…
So would you believe…
a few mins after had I posted above, readings for 11:40, 13:35 and 15:50 showed.
However, the uploads in-between these time are missing. I get notified when an upload is unsuccessful (as happend yesterday) and today there have been no such reports.
So I’m pretty sure it is a PVOutput problem.
Cheers, Jim
Mine started filling: 5:00, 6:55, 8:25. Time now is 10:03
Yeah finally catching up but still 2hrs behind abut at least coming over now!
